I.D. Mounting|Pneumatic & electric|Lightweight
The Mini MILLHOG is a ruggedly built beveling machine with a spur gear drive train and bevels all tube and pipe alloys to 6.625” O.D.
Its combination of rpm and torque also makes it ideal for tube stub removal and tube overlay and cladding removal.
All clamping components including the draw rod are heat treated and provide the strength to rigidly secure the tool on the inside diameter of the tube or pipe.
The EscoLock cutter blade holding system securely holds the cutters in the tool post and helps reduce chatter and produce a clean, continuous chip on most pipe and tube alloys without cutting fluids.
Easy to operate and maintain, this tool delivers huge performance in a small package and is available with either a pneumatic or electric motor.
MINI MILLHOG BASIC KIT #: M-200 (1) Motor and gear drive assembly (specify motor)
(1) Feed mechanism
(1) Mandrel 1.8″ (42.7mm)
(1) Draw Rod Assembly
(1) Tool post 6.625″ (168.3mm)
(2) Clamp rib/pad sets choice of (M-01 – M-05, M-08, M-011)
(1) Carrying case
(1) Operating and maintenance inst
Note:, Pneumatic motor options add:, (1) 1/2″ hose w/ filter, oiler & 3/8″ coupler
MINI MILLHOG COMPLETE KIT #: M-300 (1) Motor and gear drive assembly (specify motor) (1) Feed mechanism (1) Mandrel 1.8″ (42.7mm) (1) Draw Rod Assembly (1) Tool post 6.625″ (168.3mm) (7) Clamp rib/pad sets (M-01 – M-05, M-08, M-011) (1) Carrying case (1) Operating and maintenance inst. Note:Pneumatic motor options add:(1) 1/2″ hose w/ filter, oiler & 3/8″ coupler
MANDREL KIT (1.25″/31.8MM) PART #: M-240, The M-240 mandrel kit is designed to fit in the Mini MILLHOG gear head and will allow it to fit in tube or pipe with a 1.25″ (31.8mm) I.D. This kit works with both Cutterhead options and comes with everything needed to assemble. Clamping range of this mandrel kit is from 1.25″ (31.8mm) I.D. to 1.925″ (48.9mm) I.D., Includes, , (1) Mandrel 1.25″ (31.8mm), (1) Actuator 1.25″ (31.8mm) and draw rod assembly, (1) Draw rod stop collar, (1) Mandrel stop collar, (1) , Clamp wrench, (2) Clamp ribs H-01 & H-02,
MEMBRANE REMOVAL PART #: DEPENDENT ON SIZE (SEE CHART), Cutting head designed to remove the membrane between tubes on a boiler panel. Membrane heads use MRB-8 Inserts, and 8mm crabide bit, to remove material (same insert for overlay heads). A specific base head is required for mounting., Includes, , (1) Membrane Head (specify size), (4) Mounting Screws, NOT INCLUDED, Base Head (see size chart), Inserts, Tube Size Membrane Head Base Head # of Inserts2.5″ 63.5mm MO-113 MMB-113 72.75″ 69.9mm MO-114 MMB-113 73.0″ 76.2mm MO-115 MMB-113 8
Imperial, Working Range 1.25″ I.D. – 6.625″ O.D. Blade Series M-Series Blades Min. Width 5.3″ Head Length 14.25″ Pneumatic Electric 1.25 hp 1800 W 90 psi 120 V 40 cfm 50/60 HzCutterhead Speed 55 rpm 19-66 rpmWorking Weight 27.5 lbs 38.8 lbsShipping Weight 65 lbs 75 lbsShipping Dimensions 17″ x 31″ x 6″ 24″ x 20″ x 7″
Working Range 31.75mm I.D. – 168.3mm O.D. Blade Series M-Series Blades Min. Width 134.62mm Length 362.0mm Pneumatic Electric 932 W 1800 W 6.2 bar 220 – 240 V 1133 Lt/min 50/60 HzCutterhead Speed 55 rpm 19-66 rpmWorking Weight 12.5 kgs 17.6 kgsShipping Weight 29.5 kgs 34 kgsShipping Dimensions 432mm x 787mm x 152mm 610mm x 508mm x 178mm